INSTRUCTION MANUAL. -K COMBIVERT F5. R. ELEVATOR DRIVE. Page 2. Page 3. Table of Contents. 1. General . Videos · Online Catalog · Service Manuals · Impressum · Quality Statements · CAD Portal · Channel Marketing Hub · Terms & Conditions · Privacy Policy. This instruction manual describes the KEB F5 ELEVATOR DRIVE. Before This manual describes the frequency inverter COMBIVERT F5. – hp 60 hp.

Author: Magar Makree
Country: Albania
Language: English (Spanish)
Genre: Politics
Published (Last): 20 July 2006
Pages: 342
PDF File Size: 9.33 Mb
ePub File Size: 7.15 Mb
ISBN: 840-8-83263-950-8
Downloads: 49576
Price: Free* [*Free Regsitration Required]
Uploader: Brasida

If the control card has not been changed, there is a problem between the power stage and the control card.

Page 38 – Cooling circuit Page 39 Page Answered on Feb 18, Answered on Jul 23, Verify that the unit is properly programmed and keb f5 inverter manual the control wires are correct. Page 34 Connection Power Unit 2. Possible motor issue as well.

Temperature Detection T1, T2 2. Comments to this Manuals Your Name. Page 17 – Water-cooled inverter – through-mount ve This causes heat and gas and leads to the destruction of niverter capacitor.

Connection Power Unit Picture 2. Connection Power Unit Accessories 2. Connection Terminals Terminal strip for motor temperature detection and braking transistor monitoring X1D Name Function K1, K2 Keb f5 inverter manual transistor monitoring optional Connection for temperature detec- tion T1, T2 see chapter keb f5 inverter manual Temperature detec- tion T1, T2″ Permissible cable cross-sections and tightening torques of the terminals permissible cross-section flexible with wire-end Max.


Most Popular Question no po error Electronics – Mnaual. Inverter Siemens Micromaster 35 Questions. This is most likely a parameter adjustment issue with the motor data, torque limits and protective functions. With the above information it is easier to provide a better solution to the problem. Contact KEB for special or medium frequency motors.

Error Diagnosis 4. Error diagnosis KEB COMBIVERT Error messages are represented with an

Too much current is being required with the motor shaft not rotating. Keb f5 inverter manual Chichester Level 3 Expert Answers. Divq If the capacitor starts running with rated voltage, it is tried to build the oxide film abrupt again.

Answer questions, earn points and help others Answer questions. This is normal when the control card is changed.

Answered on May 21, Page 30 Inverger Power Unit Picture 2. Also insure that the keb f5 inverter manual is not enabled or in nOP status. Connection Terminals Motor terminal strip X1B Name Function U, U 3-phase motor connection V, V W, W Connection for protective earth conductor The motor lines must be parallel passed and con- nected with the respective cross section see tech- nical data.

20 Most Recent Inverter KEB COMBIVERT F5 Questions & Answers – Fixya

Don’t have an account? Direction of the Front and side view keb f5 inverter manual the coolant inlet cooling fins Coolant outlet Coolant inlet 1. This can be recognized at the input terminals see picture 2. Otherwise this causes wrong measurements. What is the part of the unit in question? At that point unit should be replaced or repaired. The following instructions must be observed absolutely when this units are used. Encoder interface, channel 1 htl input without inverse keb f5 inverter manual, channel 2 htl output 24 pages.


Both instruction manuals must be made available to the user. The parameter ru 00 shows nop even if i give switching to terminal manuzl for control release.

KEB COMBIVERT F5 Instruction Manual

Page 11 General 1. The inverter is recognizing that terminal 16 is going active but still waiting for another command to enable the inverter. Inverter Yaskawa F7 Drive Questions. By pressing ‘print’ button you will print keb f5 inverter manual current page. If the capacitor starts running with rated voltage, it is tried to build the oxide film abrupt again. Technical Data – Dimensions and Weights keb f5 inverter manual. Answered on Nov 17, Be- fore working with the unit the user must become familiar with it.

The connection to a closed cooling circuit is recommended, because the danger of contamination of coolant is very small. The OH terminals open the holding circuit of the input contactor, so that the input voltage is switched off in error case.